AMP RESEARCH POWER STEP – GMC / CHEVROLET
APPLICATION MODEL YR PART #
Chevrolet Silverado / GMC Sierra 1999–2006 (2007 Classic) (Crew Cab) 75113-01A
(Extended Cab) 75113-01A
Chevrolet Tahoe / Suburban 2001-2006 75115-01A
Chevrolet Avalanche * 2001-2006 (without cladding) 75115-01A
(with cladding) 75115-01A
GMC Yukon / Yukon XL 2001-2006
75115-01A
Cadillac Escalade Ext / ESV 2003–2006 75115-01A
*Modication required to running board assembly. See Item 1 page3.
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2)
Monday - Friday, 7:00 AM - 5:00 PM PST
Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:
6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975 ©2012 AMP Research. All rights reserved.
Printed in USA.
www.amp-research.com
1/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
TOOLS REQUIRED
q Safety goggles
q Measuring tape
q Flat blade screwdriver
q Phillips head screwdriver
q Right angle drill
q 1/8” drill bit
q 3/16” drill bit
q 9/32” drill bit
q 21/64” drill bit
q 17mm socket
q 13 mm socket
q 10 mm socket
q 7 mm socket
q T 20 Torx driver
q Ratchet wrench and extension
q 13mm end wrench
q Wire crimpers
q Wire stripper / cutter
q Vise grip pliers
q Corrosion inhibiter
q 3/16” hex key wrench (allen wrench)
q 5mm hex key wrench (allen wrench)
q 4mm hex key wrench (allen wrench)
q Electrical tape
q Weather proof caulking (silicone sealer)
INSTALLATION TIME
1
2 3
4
SKILL LEVEL
4= Experienced
®
TM
3-5 Hours
Professional installation recommended
5-Year Limited Warranty
AMP RESEARCH POWER STEP – GMC / CHEVROLET
INSTALLATION GUIDE
Attaching motor to linkage assembly
The motors must be attached to the linkage assemblies before continuing the
installation process.
CAUTION: HANDLE WITH CARE.
To ensure our customers receive all components with full integrity, we pack the motors separate from their linkage
assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please
follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the motor.
Instructions:
1. Position the gear cover in place as shown if not already in place.
2. Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving the
swing arms.
3. After seating into place, fasten the motor with the three motor mount screws with 4mm Hex Head. Tighten screws
to 36 in-lbs (4N-m). Do not over torque.
EXPLODED VIEW
• Motor
• Socket cap screw
• Washer
• Drive Gear Housing Cover
www.amp-research.com
2/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
USED ON SIL
VERADO
AND SIERRA
HEAVY DUTIES ONLY.
USED ON SILVERADO
AND SIERRA
HEAVY DUTIES ONLY.
2
x2
Idler linkage assembly
5
Controller STA
6
Cable Bracket
7
Brake Cable Ring
8
Drill Template
9
x4
BRACKET
(SUV SHOWN)
x2
3
x2
Motor linkage assembly
Mounting Bracket
1
x2
Running board assembly
D
B
(A) End cap left (x1)
(B) End cap right (x1)
(C) T-nut insert (x2)
(D) Socket cap screw (x2)
(E) End cap wedge right (x1)
(F) End cap wedge left (x1)
A
C
E
F
Note: Some Applications require modication.
Application Cut Length
Crew Cab, Avalanche w/o cladding
Suburban, Yukon XL, EscaladeEXT/ESV 79” (No Modication Required)
Extended Cab, Tahoe, Yukon, Escalade,
Avalanche w cladding 72” (Trim 7”)
4
Wire harness
www.amp-research.com
3/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
10
x8
Hex Head
Sheet Metal Screw
11
x4
Hex Flange Bolt
13
x4
Nylock Nut
14
x8
Button Head Bolt
15
x2
Cable tie (11”)
16
x8
Socket Cap Screw
17
Tubing (Installation Tool)
20
Grommet
18
x20
Cable tie (7”)
19
x4
Posi-Tap™ (Red/Grey)
21
x8
Hex Nut
(for Truck only- Step 8)
12
x4
Upper Sill Mount
with Stud
23
x8
Butt Connector
22
x4
LED Lamp
24
M10 Hex Bolt
25
Hex Nut
26
Single diode harness
x4
www.amp-research.com
4/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
Steps 1-3 for Heavy Duty Trucks
only! For all other vehicles skip
to Step 4.
HD - Short Bed: Remove forward most brake
cable guide.
HD - Long Bed: Remove first and third brake
cable guide.
6
Install replacement brake cable guides.
6
7
HD - L
ong Bed: Install plastic brake cable guide
in
forward hole of rear body mount.
SILL DRAIN
8
Rear linkage assembly. Template position for
Tahoe and Yukon shown in hidden lines.
Clamp drill template about 1/16” forward of the
rearmost sill drain.
Tahoe and Yukon: Clamp Template 1/8”
behind second rearmost sill drain.
8
With drill template secured with vise grips,
drill 1/8
” starter holes. Remove template and
drill holes to 21/64”
.
8
MOUNTING TAB
SILL DRAIN
FOR SUV
Front linkage assembly. Template position for
SUV driver side shown in hidden lines.
Clamp drill template to pinch weld about 1/8”
behind the
forward most mounting tab.
T
hen repeat Step 5.
SUV’s: On driver side only, clamp template
1/8” in front of forward most mounting tab.
1
3 4
5
6
2
www.amp-research.com
5/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
10
12
AVOID
DRILLING
THROUGH
WIRES.
nter the upper support mount and drill 1/8”
ter holes, then remove mount and drill 3/16”
Drill through first layer of sheet metal
. Attach with #14 sheet metal screws.
File down any exposed screw tips
from inside and cover with silicone.
Use a straight edge to ma
ke a vertical line
centered between drilled mounting holes
.
12
10
AVOID
DRILLING
THROUGH
WIRES.
File down any exposed screw tips
from inside and cover with silicone.
READ CAUTION NOTE AT TOP OF PAGE!
Repeat Steps 7 & 8 f
or rear mount. Drill through
first la
yer of sheet metal only. This mount
suppor
t will mount partially behind frame
suppor
t and will require only one sheet metal
screw
.
14
9
13
11
Mount linkage assembly and upper bracket and
finger tighten all fasteners.
Mount linkage assembly and upper bracket and
finger tighten all fasteners.
IMPORTANT NOTE:
For Truck and HD Avalanche:
T
he motorized linkage
assembly goes to the front
location on the drivers side
and to the rear location on
the passenger side.
For SUV & 1500 Avalanche:
T
he motorized linkage
assembly goes towards the
front on both sides.
2
1
16
Slide mounting
T-nut into position. Mount
board and tighten fasteners to 10 ft-lbs
. Align
the end of the board with the rear edge of the
back door
.
TIGHTEN AFTER
ADJUSTMENT
ADJUST EDGE TO
HORIZONTAL
11
T
ft-lbs. Then adjust the bottom edge to
t-lbs.
CAUTION: Remove step plates on inside of cab and move vehicle
wire harnesses out of the way before drilling in Steps 8 & 9.
7
9
10
12
8
11
www.amp-research.com
6/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
www.amp-research.com
6/11
INSTALLATION GUIDE
AMP RESEARCH POWER STEP – GMC / CHEVROLET
4
5
Using the two 11” cable ties, mount controller to
fa
ctory wire conduit above brake booster on
driv
ers side of truck.
Plug in wire harness.
(Ensure that locking
tabs engage.)
15
4
4
Route long end of wire harness ab
ove engine
and down through passenger side wheel well.
Zip tie harness to cowling clips on fire wall
.
Route shor
t end down drivers side.
Secure with zip ties.
4
Route wire harness along the frame. Secure
with zip ties
.
4
3
Poke hole through rubber grommet near
front door on underside of floor panel with
small phillips screwdriv
er. Push both wires
through hole
.
(See Step 20 f
or passenger side notes.)
Plug wire
harness into
motors.
24
Remove power fuse. Attach power lead RED wire
to positive lead in the junction box. CAUTION:
Do not ground wrench when engaged with nut.
Attach ground lead to junction box mount-
ing bracket. (See Step 15 for Diesel Engine
grounding location)
Diesel Models only! Using supplied Hex Head
Screw connect ground to air compressor mount-
ing bracket.
16
17
16
13 14
18
17
15
13
www.amp-research.com
7/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
www.amp-research.com
7/11
INSTALLATION GUIDE
AMP RESEARCH POWER STEP – GMC / CHEVROLET
IMPORTANT: Steps 21 and 22 are for Crew Cabs and SUV’s only. Light blue and Green wires will
not be used otherwise. See end of install sheet for 1999-2002 model year wiring
4
Pull up the carpet and thread both wires
through the floor panel (same steps on passen-
ger side EX
CEPT drill 9/32” hole in metal and
add rubber grommet)
.
Seal holes with silicone glue.
See wire diagrams for model
years previous to 2003.
On Crew Cab’s and SUV’s carefully remove wire
wrap. On drivers side find the LIGHT BLUE wire
with BLACK STRIPE. On the passenger side find
GREEN wire with BLACK STRIPE rear of the “T”
junction where wires cross under the front seat).
19
4
Remove plastic trim on door
near mirror attachment
.
T
o remove door, first pry off door lock
ta
b. Remove door bolts.
Using supplied Posi-Taps™ splice shorter
trigger wire into wire found in step 21.
Note: Crew Cab and SUV’s only; these
wires not used for Extended Cabs, Cut
and tape o.
Pop off the threshold cover with screwdriver and
remove the kick panel. The panel will slide out
from under the seat after fasteners give way.
19 20
21 22
23 24
www.amp-research.com
8/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
Pry off door handle plate and any remaining
panel fasteners.
Then remove door panel.
NOTE: Remove door light
while removing door panel.
17
Pull back the door weather guard. Pry off
speaker and unplug
. Thread plastic tube
through accordion.
4
4
17
Feed longer wire of Step 20 through tube into
door and pull out plastic tube on door side
.
4
Route wire along harness going to switch plate.
4
19
Secure all wires with zip ties and electrical tape.
Using supplied Posi-Taps™ splice trigger
wire into door ajar wire (Driver side: Gray
with Black Stripe; Passenger side: Black with
White Stripe). The trigger wires will attach to
the connector with a cam-release lever.
27 28
25 26
29 30
www.amp-research.com
9/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
AMP RESEARCH POWER STEP – GMC / CHEVROLET
Replace power fuse.
On each side of the vehicle measure from the front
edge of door line on the pinch weld to the specied
lengths below. Measure at 22” for front LED Light
and 65” for rear LED Light.
Ax lamp to rocker panel surface. Make sure the
lamp is axed to a clean, at surface. There is a
step down midway across the surface. Ax lamp
just outside of step down.
Using supplied butt connectors, connect the lamp
wires. Red to Red, Black to Black. Once Crimped
use heat gun to shrink tube.
Close and wrap with conduit and electrical tape.
Secure all loose wires with cable ties, with lamp wires
pulled upward to avoid any wire snagging.
Replace power fuse
22
23
Make sure that plug lever is fully opened before
reinstalling
. Failure to do this will adversely
af
fect the operation of the powerstep and
window controls
.
Reinstall door panel.
36
32
33 34
31
35
36
www.amp-research.com
10/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
www.amp-research.com
10/11
INSTALLATION GUIDE
AMP RESEARCH POWER STEP – GMC / CHEVROLET
Check that all doors activate the Power Step and the LED Lights work when doors open and
close. Reinstall any remaining trim panels.
CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any door of vehicle. Lamps
will stay on until restowing of both Power Steps or until 5 minutes has expired with the doors open. When the
lights timeout after 5 minutes, they can be reillumintated by closing and opening any door of vehicle.
FINAL SYSTEM CHECK
Check that all doors activate the PowerStep and the LED lights work when doors open and close.
NORMAL OPERATION: When the doors open, PowerStep automatically deploys from under the vehicle.
When the doors are closed, PowerStep will automatically return to the stowed/retracted position. Note that
there is a 2-second delay before the PowerStep returns to the stowed/retracted position.
32
www.amp-research.com
11/11
INSTALLATION GUIDE
IM75113 rev 04.29.21
www.amp-research.com
11/11
INSTALLATION GUIDE
Slight adjustments to the upper mount can
be made to adjust stow positon. With the
board extended, loosen hex bolt as shown,
adjust as needed, and retighten hex bolt to
16 ft-lbs.
The adjustments will be made to
either increase or decrease the gap between
the board and rocker panel when stowed.
decreases gap
increases gap
5. After removing the door panel, you will access
the wire bundle at
the black cam-plug from window control panel (Area-A). Undo wire
wrap and locate the 18Ga. door-ajar signal wire (grey with a black
stripe).
6.
7. The longer of the two wires from step-1 will be routed to the door
panel through front door accordian. Attach routed wire from
Powerstep harness to Posi-Tap connector.
1. After removing the front door step plate, lift carpet and pull
Powerstep trigger wires through floor of truck.
2. Open wire bundle located under front door step plate and locate
the 18Ga. rear door-ajar signal wire (light blue with a black stripe).
3. Apply Posi-Tap connector to the above found wire.
4.
Notes:
1. All of the signal wires tapped into will be 18Ga. Do not tap into anything with a thicker gage than this.
2. Occassionally the wire colors do not match the wire schematics. Under these circumstances you will need to locate the door-ajar signal wires.
3. Make sure to secure all wires after install. Loose wires can be da
maged and may cause a failure in the Powerstep's function.
Rear of Truck
Green / Black from
Vehicle Harness
Front of Truck
Green / Black wire
from Powerstep
Harness
Passes under
front seat.
1. After removing the front door step plate, lift carpet and pull
Powerstep trigger wires through floor of truck.
2. Open wire bundle located under front door step plate and locate
the 18Ga. rear door-ajar signal wire (green with a black stripe).
PASSENGER SIDE WIRING
D
Revision - 04/29/21
Black/White wire
from Powerstep
Harness
Black/White wire
from Powerstep
Harness
5. After removing the door panel, you will access the wire
bundle at the black cam-plug from window control panel (Area
-C). Undo wire wrap and locate the 18Ga. door-ajar signal
wire (black with a white stripe).
C
PASSENGER SIDE
Wiring Instructions
GM POWERSTEP ('03-'06) Truck & SUV, ('07 Classic Truck)
C
D
L-Blue / Black wire
from Powerstep
Harness
Front of Truck
B
L-Blue/ Black from
Vehicle Harness
Rear of Truck
B
A
Grey / Black wire
from Powerstep
Harness
A
DRIVER SIDE WIRING
DRIVER SIDE
Insert
Tighten
Strip 3/8”
Insert and
Tighten
Posi-Tap instructions
Strip wire back approx 3/8” and attach to Posi-Tap connector.
Apply Posi-Tap connector to the above found wire.
3. Apply Posi-Tap connector to the above found wire.
4.
Strip wire back approx 3/8” and attach to Posi-Tap connector.
6.
7. The longer of the two wires from step-1 will be routed to the door
panel through front door accordian. Attach routed wire from
Powerstep harness to Posi-Tap connector.
Apply Posi-Tap connector to the above found wire.
®
Power Step
Trigger Wire
Leads to Front door Panel.
Diode
Figure A-3
Power Step
Trigger Wire
Leads toward
rear of vehicle.
Figure A-2
Diode
Wiring Instructions
GM POWERSTEP
1999-2002 Truck & SUV - LUXURY & UP LEVEL
DRIVER SIDE WIRING
PASSENGER SIDE WIRING
1. After removing the front door step plate and kick plate, lift carpet
and pull Powerstep trigger wires through floor of truck.
2. Locate the rear door-ajar signal wire (dark blue with white stripe)
on black connector below the hood-release lever (Area-A in Figure A
-1). There should be two wires of this color; use the wire located on
the row closest to the plug release.
3. Cut this wire and install Single Diode Harness as oriented in
Figure A-2.
4. After timming to correct length, connect the light blue with black
stripe trigger wire from step one to the blue connector of Single
Diode Harness installed in previous step.
5. Locate the front door-ajar signal wire (tan) on large connector
located behind the connector of step 2.
6. Cut this wire and install Single Diode Harness as oriented in
Figure A-3.
7. After timming to correct length, connect the grey with black
stripe trigger wire from step one to the blue connector of Single
Diode Harness installed in previous step.
8. Wrap all connections with electrical tape an
d secure any loose
wires.
Notes:
1. All of the signal wires tapped into will be 18Ga. Do not tap into anything with a thicker gage than this.
2. Occassionally the wire colors do not match the wire schematics. Under these circumstances you will need to locate the door-ajar signal wires.
3. Make sure to secure all wires after install. Loose wires can be damaged and may cause a failure in the Powerstep's function.
Diode
Diode
1. After removing the front door step plate, lift carpet and pull
Powerstep trigger wires through floor of truck.
2. Locate the two wire bundles running up along kick panel area
underneith glove compartment as shown in the above figures.
3. Open wire wrap of the bundles and locate the front and rear door-
ajar signal wires (dark blue with white stripe), one found in each
bundle.
B
Figure B-1
4. Cut each wire and install the Single Diode Harnesses as
oriented in Figure B-2. Make certain that the leg with the
diode is towards the top.
5. Wrap all connections with electrical tape and secure any
loose wires.
Figure B-2
Revision - 04/29/21
A
Figure A-1
ATTENTION: Pay close attention to the
orientation of the diode harnesses. The
Power-Step will not work with a incorrectly
installed diode harness.
®
Power Step
Trigger Wire
Leads to Front door Panel.
Diode
Figure A-3
1. After removing the front door step plate and kick plate, lift carpet
and pull Powerstep trigger wires through floor of truck.
2. Locate the rear door-ajar signal wire (orange) on black connector
below the hood-release lever (Area-A in Figure A-1). There should
be two wires of this color; use the wire located on the row closest to
the plug release.
3. Cut this wire and install Single Diode Harness as oriented in
Figure A-2.
4. After timming to correct length, connect the light blue with black
stripe trigger wire from step one to the blue connector of Single
Diode Harness installed in previous step.
5. Locate the front door-ajar signal wire (tan) on large connector
located behind the connector of step 2.
6. Cut this wire and install Single Diode Harness as oriented in
Figure A-3.
7. After timming to correct length, connect the grey with black
stripe trigger wire from step one to the blue connector of Single
Diode Harness installed in previous step.
8. Wrap all connections with electrical tape and secure any loose
wires.
Diode
Diode
Notes:
1. All of the signal wires tapped into will be 18Ga. Do not tap into anything with a thicker gage than this.
2. Occassionally the wire colors do not match the wire schematics. Under these circumstances you will need to locate the door-ajar signal wires.
3. Make sure to secure all wires after install. Loose wires can be damaged and may cause a failure in the Powerstep's function.
PASSENGER SIDE WIRING
Figure B-1
B
1. After removing the front door step plate, lift carpet and pull
Powerstep trigger wires through floor of truck.
2. Locate the two wire bundles running up along kick panel area
underneith glove compartment as shown in the above figures.
3. Open wire wrap of the bundles and locate the front and rear door-
ajar signal wires (dark blue with white stripe), one found in each
bundle.
4. Cut each wire and install the Single Diode Harnesses as
oriented in Figure B-2. Make certain that the leg with the
diode is towards the top.
5. Wrap all connections with electrical tape and secure any
loose wires.
Figure B-2
Revision - 04.29.21
Power Step
Trigger Wire
Leads toward
rear of vehicle.
Figure A-2
Diode
Wiring Instructions
GM POWERSTEP
1999-2002 Truck & SUV - BASE LEVEL
DRIVER SIDE WIRING
A
Figure A-1
ATTENTION: Pay close attention to the
orientation of the diode harnesses. The
Power-Step will not work with a incorrectly
installed diode harness.
®
1. After removing the front door step plate and kick plate, lift carpet
and pull Powerstep trigger wires through floor of truck.
2. Locate the rear door-ajar signal wire (dark blue with white stripe)
wire on black connector below the hood-release lever (Area-A in
Figure A-1). There should be two wires of this color; use the wire
located on the row closest to the plug release.
3. Cut this wire and install Single Diode Harness as oriented in
Figure A-2.
4. After timming to correct length, connect the light blue with black
stripe trigger wire from step one to the blue connector of Single
Diode Harness installed in previous step.
5. Locate the front door-ajar signal wire (light green with black
stripe) on large connector located behind the connector of step 2.
6. Cut this wire and install Single Diode Harness as oriented in
Figure A-3.
7. After timming to correct length, connect the grey with black stripe
trigger wire from step one to the blue connector of Single Diode
Harness installed in previous step.
8. Wrap all connections with electrical tape and secure
any loose
wires.
Diode
Diode
Notes:
1. All of the signal wires tapped into will be 18Ga. Do not tap into anything with a thicker gage than this.
2. Occassionally the wire colors do not match the wire schematics. Under these circumstances you will need to locate the door-ajar signal wires.
3. Make sure to secure all wires after install. Loose wires can be damaged and may cause a failure in the Powerstep's function.
PASSENGER SIDE WIRING
Figure B-1
B
1. After removing the front door step plate, lift carpet and pull
Powerstep trigger wires through floor of truck.
2. Locate the two wire bundles running up along kick panel area
underneith glove compartment as shown in the above figures.
3. Open wire wrap of the bundles and locate the rear door-ajar signal
wire (dark blue with white stripe) in one bundle and the front door-
ajar signal wire (light green with black stripe) in the other bundle.
4. Cut each wire and install the Single Diode Harnesses as
oriented in Figure B-2. Make certain that the leg with the
diode is towards the top.
5. Wrap all connections with electrical tape and secure any
loose wires.
Figure B-2
Revision - 04/29/21
Power Step
Trigger Wire
Leads toward
rear of vehicle.
Figure A-2
Diode
Wiring Instructions
GM POWERSTEP
1999-2002 Sierra Denali Only
DRIVER SIDE WIRING
A
Figure A-1
Power Step
Trigger Wire
Leads to Front door Panel.
Diode
Figure A-3
ATTENTION: Pay close attention to the
orientation of the diode harnesses. The
Power-Step will not work with a incorrectly
installed diode harness.
®
™
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR
FASTER SERVICE & PRODUCT UPDATES
Please visit:
www.amp-research.com/productregistration
or scan the QR Code
Product Registration Benefits:
• Ensure we have your purchase receipt and product info in our
system which is required for warranty
• Faster and easier access to customer service and tech support in
the unlikely event you need warranty or product support
• Registration helps us keep you up to date on product information
and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Rev 01.05.21
Automatic power deploy:
The running boards will extend down and out when the doors are opened.
Automatic power stow:
The running boards will return to the stowed position when the doors are closed. There will be a 2-second
delay before the running boards move to the stowed position.
Automatic stop:
If an object is in the way of the moving running board, the running board will automatically stop.
To reset, clear any obstruction, then simply open and close the door to resume normal operation.
Manually set in the deployed (OUT) position for access to the roof:
your foot while at the same time closing the door. To resume normal operation, open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running
board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to
Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins.
Do not apply silicone, wax or protectants like Armor All® to the running board stepping surface.
Caution! Keep hands away when the running board is in motion.
™
Congratulations on your purchase of the
genuine AMP Research PowerStep!
Here’s what you should know...
AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM
DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair replacement of the product itself, or the repair
or replacement of any component part thereof, found by the factory to be defective within the time period specied. The
decision to repair or replace is wholly within the discretion of the manufacturer.
for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon
completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage
to our products caused by accidents, re, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts
not manufactured by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE
LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some stat
es do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic
legal rights, and you may also have other rights that vary from state to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH CUSTOMER SERVICE 1-888-983-2204
5-YEAR LIMITED WARRANTY
WARNING
Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle
occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed.
AMP Research PowerStep running boards automatically move
when the doors are opened to assist entering and exiting the vehicle.